Slotket Sammelthread (Sockel 370-Slot 1 Adapter)

  • Ich habe noch folgende Adapter auftreiben können:


    AA370TS Ver. 1.0



    370SP Rev. 2.0



    Beide sind wohl nur Coppermine fähig.

    Meine Vintagerechner: XT (NEC V20) & Book8088 (v2, VGA) #-# Epson XT portable #-# HighScreen 286@16MHz #-# L&P 286-20MHz #-# Cyrix 386DRx²-33/66 #-# ESCOM Black Slim Am386DX@40MHz #-# SCT Proline Cyrix486DX2@66 #-# Cyrix 5x86@100 VIP #-# Libretto 50CT #-# && 1x Sockel 8 & 3x Sockel4 (60MHz + 66MHz)

  • Ich hab hier noch etwas staubfreiere Bilder vom AA370TS VER 1.0 ;)





    (Wollte die eigentlich gestern schon vor nicetux posten, bin jedoch nicht dazu gekommen, deshalb nun trotzdem, damit es die Mühe wert war... :saint: )


    Anbei noch die Dokumentation der Jumper Settings von der Verpackungsrückseite:


    Demnach soll der Slotket neben dem Celeron sowie dem Coppermine P3s noch mit dem VIA/Cyrix Joshua kompatibel sein.

  • Aktuell lese ich in Via C3 Nehemiah Datenblatt, ob ich damit Chance mit 2x CPU Betrieb habe... (Wohl ja, aber selbst Asus S370-DL müsste modifiziert werden) Edit: P2B-DS hat keine Mircocode für Nehemiah.


    Nehemiah ist neuste Socket 370 CPU und erfordert Tualatin fähige Mainboard.

    Ich hocke auf ca 50 Stück C3 1.0A Ghz

    Die haben sogar nen extra CPU Kern..


    https://github.com/xoreaxeaxeax/rosenbridge


    The rosenbridge backdoor is a small, non-x86 core embedded alongside the main x86 core in the CPU. It is enabled by a model-specific-register control bit, and then toggled with a launch-instruction. The embedded core is then fed commands, wrapped in a specially formatted x86 instruction. The core executes these commands (which we call the 'deeply embedded instruction set'), bypassing all memory protections and privilege checks.

    совок

  • Guten Morgen,


    ich möchte zwei MSI MS 6905 Master in Rev 2.3 auf einem ASUS P2B-DS Rev 1.06 D03 verwenden.
    Ich blicke nu die Jumpereinstellung nicht, bzw. verstehe nicht warum ich weder zwei 1000er Celeron noch zwei 667er P3 zum laufen bekomme.

    Die SLotket haben nur 3 statt 2 Pins auf der besagten Jumperbrücke, laut Anleitung sind dort aber 4.

    Einzeln laufen die Adapter tadellos, auch mit einem 1400s (getesten auf einem BH6)

    Benötige ich den Kabelmod noch?

    Gruß, Karsten

  • Die MSI Master sind ohne Mod nicht dual-fähig.

    Slot-Coppermine Pentiums laufen problemlos, Slot-Coppermine Celerons nicht im Dual-Modus.

    Daily Driver: MSI X470 Gaming Plus - Ryzen 7 1700 - 32 GB - Geforce GTX 1060 6GB - 1 TB NVMe SSD - 2 x 1 TB Raid-0 SATA

    Projekt #1: ASI 486-33 - Projekt #2: PC Chips M912 486 VLB - Projekt #3: Biostar MB8500TVX-A Pentium MMX 166 - Projekt #4: ASUS TXP4 K6-III 400 - Projekt #5: Gigabyte GA-6BXDS Dual Slot 1 PIII-650 -

    Projekt #6: ASUS P2B-DS Dual Slot 1 PIII-1000 - Projekt #7: Gigabyte GA-6VXD7 Dual Sockel 370 PIII-1000 - Projekt #8: TYAN S2505T Dual Tualatin 1400

  • Ok, also obwohl laut Anleitung Dualfähig und sogar eine Einstellung der Jumper für DualCoppermine brauch ich die Drahtbrücke?


    Muss ich diese an beiden Adapter modifizieren?

    Ich möchte dann auf dem Board zwei 1400s laufen lassen. Die 1400s sind mittels Platine gemoddet (läuft ja schon einzeln auf den Adaptern). Muss ich da dann noch etwas beachten?


    Gruß, Karsten

  • http://www.oocities.org/_lunchbox/ms6905_tualatin_mod.html



    Table 1

    Model

    Description

    Picture

    MS-6905 1.0 Celeron-Only operation(66 FSB). No jumper for 100 FSB/B21 or jumpers for VID selection. Silk screen for jumper shows up in later copies of this model. Picture
    MS-6905 1.1 Dual Added jumpers for VID 1.8-2.4v and Dual-Proc selection. No jumper for FSB 100/B21 operation.

    Picture

    MS-6905 1.1 Dual (Rev. A) Added jumper for Dual-Proc operation. Adapter was manufactured to be stable at FSB 133. Some Rev. A adapters came without J2 soldered in. Picture
    MS-6905 1.1 Dual (Rev. B) Added J4 for FSB 133 selection and plastic retention mechanism. Intended to support Pentium3. Was recalled by MSI since Pentium3 support was flawed. No Pic
    MS-6905 Master 2.0 & 2.3 Added TVC chip and plastic retention mechanism, J4 for FSB 133, support for Coppermine 256k. Ver 2.0 has 3 pin J3 and Ver 2.3 has 4 pin J3. 2.0

    2.3


    Der 2.3 sollte eigentlich Jumper für Dual Betrieb haben.

    Bin mir nur nicht mehr Sicher ob das nicht nur mit dem Celeron Mendoccino ging.

    совок

  • Ja, der Mod muss an beiden Adaptern durchgeführt werden.

    Daily Driver: MSI X470 Gaming Plus - Ryzen 7 1700 - 32 GB - Geforce GTX 1060 6GB - 1 TB NVMe SSD - 2 x 1 TB Raid-0 SATA

    Projekt #1: ASI 486-33 - Projekt #2: PC Chips M912 486 VLB - Projekt #3: Biostar MB8500TVX-A Pentium MMX 166 - Projekt #4: ASUS TXP4 K6-III 400 - Projekt #5: Gigabyte GA-6BXDS Dual Slot 1 PIII-650 -

    Projekt #6: ASUS P2B-DS Dual Slot 1 PIII-1000 - Projekt #7: Gigabyte GA-6VXD7 Dual Sockel 370 PIII-1000 - Projekt #8: TYAN S2505T Dual Tualatin 1400

  • Ja, leider ist auch Lötarbeit nötig, siehe meine Bilder in erste Seite.

    Jumper 'Dual CPU'" ist nur für Mendocino Celeron gerüstet. (Bzw. Coppermine, dafür falsche Pin)

  • MSI MS6905 Ver2.3, die besagten Adapter.



    nun mal in Ruhe schauen, wo das Kabel hin muss.

    Da ja der J3 nur aus drei Pins besteht, bin ich mir da unsicher, aber ich geh mal davon aus, das der dann wie Ver 2 ist, oder?
    Die Drahtbrücke scheint zumindest immer die selbe zu sein.


    Kann ich ein höher aufgelöstes Bild von der Version 2 mit dem Draht bekommen?


    Gruß, Karsten

  • Sieht nach einem normalen CuMine Adapter aus.

    Compaq Deskpro 286n/12MHz - 1MB - 40MB HDD - 3,5" Floppy //
    Panatek 386DX33 - 80387 - 8MB - 504MB CF2IDE - 5.25" & 3,5" Floppy - SB Vibra - NIC - 512Kb VGA //
    486DX2-66 - 16MB - 4GB CF2IDE - 5,25" & 3,5" 2,88MB Floppy - DVD - SB Vibra - NIC - 1MB CL VLB VGA //
    Intel Pentium 233MMX - 64MB - 16GB CF2IDE - 3,5" Floppy - DVD - SB AWE64 - NIC - 3Dfx Voodoo Banshee//
    Intel Pentium III 600MHz - 256MB - 4GB CF2IDE - 3,5" Floppy - DVD - SB AWE64 - NIC - 3Dfx Voodoo 3 3000 //


  • ;)

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!