Beiträge von moravec

    YT:

    Externer Inhalt www.youtube.com
    Inhalte von externen Seiten werden ohne Ihre Zustimmung nicht automatisch geladen und angezeigt.
    Durch die Aktivierung der externen Inhalte erklären Sie sich damit einverstanden, dass personenbezogene Daten an Drittplattformen übermittelt werden. Mehr Informationen dazu haben wir in unserer Datenschutzerklärung zur Verfügung gestellt.


    Externer Inhalt www.youtube.com
    Inhalte von externen Seiten werden ohne Ihre Zustimmung nicht automatisch geladen und angezeigt.
    Durch die Aktivierung der externen Inhalte erklären Sie sich damit einverstanden, dass personenbezogene Daten an Drittplattformen übermittelt werden. Mehr Informationen dazu haben wir in unserer Datenschutzerklärung zur Verfügung gestellt.

    die hat vor allem 147 MB und nicht nur 40 wie die anderen...

    habe erste Schritte mit dem Board probiert - bin aber gescheitert mehr als DX4-100 rauszubekommen, obwohl ich dachte auf DX4 120 gejumpert zu haben; schien mir nicht so intuitiv, habs dann erstmal zur Seite getan...

    habe gerade ChatGPT nach Jumper und Dip Switch Settings gefragt - ausführliche Antwort:


    The Sanyo MBC 16EX5 XT PC series is a vintage computer system that was released in the late 1980s. Here are the jumper and dip switch settings for this system:

    Jumper settings:

    • JP1: This jumper is used to enable/disable the onboard clock/calendar chip. To enable the chip, the jumper should be installed on pins 1 and 2. To disable it, the jumper should be removed.
    • JP2: This jumper is used to select the base memory size. If the system has 256KB of base memory, the jumper should be installed on pins 2 and 3. If it has 512KB of base memory, the jumper should be installed on pins 1 and 2.
    • JP3: This jumper is used to enable/disable the external cache. To enable the cache, the jumper should be installed on pins 1 and 2. To disable it, the jumper should be removed.
    • JP4: This jumper is used to select the video mode. If the system is using an MDA or Hercules monochrome display, the jumper should be installed on pins 1 and 2. If it is using a CGA color display, the jumper should be installed on pins 2 and 3.

    Dip switch settings:

    • SW1: This dip switch is used to select the DMA channel for the floppy disk controller. If the floppy disk controller is using DMA channel 2, the switch should be set to OFF. If it is using DMA channel 3, the switch should be set to ON.
    • SW2: This dip switch is used to select the IRQ channel for the mouse. If the mouse is using IRQ 3, the switch should be set to OFF. If it is using IRQ 4, the switch should be set to ON.
    • SW3: This dip switch is used to select the COM port address for the serial port. If the serial port is using COM1 (address 3F8h), the switch should be set to OFF. If it is using COM2 (address 2F8h), the switch should be set to ON.
    • SW4: This dip switch is used to select the IRQ channel for the serial port. If the serial port is using IRQ 4, the switch should be set to OFF. If it is using IRQ 3, the switch should be set to ON.

    Please note that these settings may vary depending on the specific configuration of your Sanyo MBC 16EX5 XT PC system. Be sure to consult the system manual or contact the manufacturer for more information if you are unsure about any of these settings.